Linux cli command proc_pid_clear_refs

➡ A Linux man page (short for manual page) is a form of software documentation found on Linux and Unix-like operating systems. This man-page explains the command proc_pid_clear_refs and provides detailed information about the command proc_pid_clear_refs, system calls, library functions, and other aspects of the system, including usage, options, and examples of _. You can access this man page by typing man followed by the proc_pid_clear_refs.

  2 minute read  

NAME 🖥️ proc_pid_clear_refs 🖥️

reset the PG_Referenced and ACCESSED/YOUNG bits

DESCRIPTION

/proc/pid/clear_refs (since Linux 2.6.22)

This is a write-only file, writable only by owner of the process.

The following values may be written to the file:

1 (since Linux 2.6.22)
Reset the PG_Referenced and ACCESSED/YOUNG bits for all the pages associated with the process. (Before Linux 2.6.32, writing any nonzero value to this file had this effect.)

2 (since Linux 2.6.32)
Reset the PG_Referenced and ACCESSED/YOUNG bits for all anonymous pages associated with the process.

3 (since Linux 2.6.32)
Reset the PG_Referenced and ACCESSED/YOUNG bits for all file-mapped pages associated with the process.

Clearing the PG_Referenced and ACCESSED/YOUNG bits provides a method to measure approximately how much memory a process is using. One first inspects the values in the “Referenced” fields for the VMAs shown in /proc/pid/smaps to get an idea of the memory footprint of the process. One then clears the PG_Referenced and ACCESSED/YOUNG bits and, after some measured time interval, once again inspects the values in the “Referenced” fields to get an idea of the change in memory footprint of the process during the measured interval. If one is interested only in inspecting the selected mapping types, then the value 2 or 3 can be used instead of 1.

Further values can be written to affect different properties:

4 (since Linux 3.11)
Clear the soft-dirty bit for all the pages associated with the process. This is used (in conjunction with /proc/pid/pagemap) by the check-point restore system to discover which pages of a process have been dirtied since the file /proc/pid/clear_refs was written to.

5 (since Linux 4.0)
Reset the peak resident set size (“high water mark”) to the process’s current resident set size value.

Writing any value to /proc/pid/clear_refs other than those listed above has no effect.

The /proc/pid/clear_refs file is present only if the CONFIG_PROC_PAGE_MONITOR kernel configuration option is enabled.

SEE ALSO

proc(5)

░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░

  █║▌│║█║▌★ KALI ★ PARROT ★ DEBIAN 🔴 PENTESTING ★ HACKING ★ █║▌│║█║▌

              ██╗ ██╗ ██████╗  ██████╗ ██╗  ██╗███████╗██████╗
             ████████╗██╔══██╗██╔═══██╗╚██╗██╔╝██╔════╝██╔══██╗
             ╚██╔═██╔╝██║  ██║██║   ██║ ╚███╔╝ █████╗  ██║  ██║
             ████████╗██║  ██║██║   ██║ ██╔██╗ ██╔══╝  ██║  ██║
             ╚██╔═██╔╝██████╔╝╚██████╔╝██╔╝ ██╗███████╗██████╔╝
              ╚═╝ ╚═╝ ╚═════╝  ╚═════╝ ╚═╝  ╚═╝╚══════╝╚═════╝

               █║▌│║█║▌ WITH COMMANDLINE-KUNGFU POWER █║▌│║█║▌

░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░